A boiler that won't fire up, or one that has started gurgling, whistling or banging, is one of the most common reasons people call a heating engineer. Some causes are simple and safe to check yourself. Others need a qualified engineer.
This guide covers the usual reasons a boiler stops working, what the different noises tend to mean, and when it is time to book a repair.
Smell gas? Don't touch any switches. Open windows, turn off the gas at the meter if you can, leave the property and call the National Gas Emergency Service on 0800 111 999.
Why won't my boiler fire up?
These are the most common reasons a boiler won't light or keeps locking out:
- Low pressure. If the pressure gauge reads below about 1 bar when the system is cold, most boilers will stop working and show a fault code.
- Thermostat or controls. The room thermostat or timer may not be asking for heat, the batteries may be flat, or the settings may have been changed.
- Frozen condensate pipe. In cold weather the plastic pipe that carries water from a condensing boiler to the drain can freeze, and the boiler shuts down to protect itself.
- Gas supply. A problem with the gas supply, or no credit on a prepayment meter, will stop the boiler lighting.
- Power. A tripped fuse, a switched-off fused spur or a power cut will stop it starting.
- A faulty part. Ignition faults, a failed fan, pump or diverter valve, or a blocked burner need an engineer to diagnose.
Safe checks to try first
Work through these before calling anyone. None of them involve opening the boiler casing, which you should never do yourself.
1. Check the pressure
Look at the gauge on the boiler. If it is below about 1 bar with the heating off and cold, top it up with the filling loop. Our boiler pressure guide shows how, step by step.
2. Check the thermostat and timer
- Make sure the thermostat is set higher than the current room temperature.
- Replace the batteries if it is battery powered.
- Check the timer or app is set to "on" for the time you want heat.
3. Check the condensate pipe in cold weather
Find the white or grey plastic pipe that runs from the boiler to a drain, often outside. If it is frozen, pour warm (not boiling) water along it, or hold a warm water bottle against it, then reset the boiler.
4. Check the gas and power
- Check whether your other gas appliances, such as the hob, are working.
- If you have a prepayment meter, check it has credit.
- Check the boiler's fused spur is switched on and the fuse board hasn't tripped.
5. Reset the boiler
Most boilers have a reset button or a reset option on the display. Your boiler's manual explains how. If the boiler locks out again straight away, or keeps showing the same fault code, stop resetting it and book an engineer.
6. Bleed the radiators
If the boiler runs but some radiators are cold at the top, there is air in the system. Turn the heating off, let the radiators cool, then open each bleed valve slightly with a radiator key until water appears. Bleeding can lower the pressure, so check the gauge afterwards.
What is that noise?
Boilers make some noise when they run, and a little clicking as the boiler lights or the pipes warm up is normal. Noises that are new, loud or getting worse usually point to one of these:
Gurgling or bubbling
Usually air in the system. Bleed the radiators and check the pressure. In winter, a gurgle from a condensing boiler can also mean the condensate pipe is starting to freeze.
Whistling or "kettling"
A sound like a kettle coming to the boil usually means limescale or sludge has built up in the heat exchanger, so water is overheating as it passes through. This needs an engineer, who may recommend cleaning the system (a flush) and fitting or cleaning a magnetic filter.
Banging or knocking
Can be severe kettling, a pump problem, delayed ignition or loose pipework. Loud banging from the boiler itself should be looked at by an engineer rather than ignored.
Humming or vibrating
Often the pump, either set at the wrong speed or starting to wear, or a loose part. An engineer can check the pump and adjust or replace it.
Frequent loud clicking
Occasional clicks are normal. Repeated clicking with no flame lighting can mean an ignition fault, which needs an engineer.
When to call a heating engineer
Book a repair if:
- the boiler still won't fire up after the checks above
- the same fault code keeps coming back
- you need to top up the pressure regularly, or water is leaking
- the boiler is kettling, banging or humming loudly
- you can see scorch marks, or the flame looks yellow or orange instead of blue
Any work on the boiler itself or the gas supply must be done by a Gas Safe registered engineer.
Preventing breakdowns
An annual boiler service is the best way to catch worn parts, check the boiler is burning safely and keep your manufacturer's warranty valid. Between services, keep an eye on the pressure, bleed radiators when they have cold spots, and lag any outside condensate pipe before winter.
Need a boiler repair in London?
Heatmaster London repairs and services boilers across London, from our base in Barnet, North London. You can book a repair or service online in a couple of minutes, read more about our boiler work, or see our FAQs.